Verilink QUAD DATA (880-503319-001) Product Manual Bedienungsanleitung PDF herunterladen (Seite 18)

Quick Set-Up

2-4 Verilink QUAD DATA User Manual

2. Use the

and

commands to place ports 2 and 3 in service.

3. Port 1 is set to V.35 by default. Use the

command to select

EIA 530 for port 2, then use the

command to select RS-449

for port 3. Since the QUAD DATA module is Data

Communications Equipment (DCE), and Data Terminal

Equipment (DTE) is being connected, the default setting of DCE

for data port mode is correct.

4. Port 1 of the QUAD DATA module is to carry Cisco™ router

traffic. Since these routers wrap the DSU transmit clock signal

back to the QUAD DATA Module on the optional third clock

pair (TT in RS-449, SCTE in V.35), the port 1 clock option will

be set to TT. Type “C1” and select “3” for TT. Leave ports 2

and 3 at the default value of ST.

5. There is no benefit gained by dis-allowing loopback testing.

Set the

Allow Loopback

Allow LoopbackAllow Loopback

Allow Loopback

option to Yes for ports 1 through 3 by

using the

, and

commands.

6. The transmit timing options for the QUAD DATA module are

accessed through a submenu. Type “T” to access the timing

options submenu.

Figure 2-3 Timing Options

Timing Options

The

Timing Options Menu

is maintained by the SCM and applies to

every T1 and QUAD DATA module in the shelf. When the QUAD T1

module was installed in slot 4 of this shelf, this menu was

configured so that the first three network ports of the QUAD T1

module provide the three levels of timing source.

Under normal circumstances the T1 facility connected to network

port 1 of the QUAD T1 module is the transmit timing source for the

shelf. If that T1 fails, the second network port becomes the timing

source. Should both fail, network port 3 becomes the timing

-- QUAD DATA CONFIGURATION MENU (TIMING OPTIONS)--

-- QUAD DATA CONFIGURATION MENU (TIMING OPTIONS)---- QUAD DATA CONFIGURATION MENU (TIMING OPTIONS)--

-- QUAD DATA CONFIGURATION MENU (TIMING OPTIONS)--

Current shelf timing source: card 4, net 1 (primary)

Current shelf timing source: card 4, net 1 (primary)Current shelf timing source: card 4, net 1 (primary)

Current shelf timing source: card 4, net 1 (primary)

Source Slot Number Synchronization Auto Restore

Source Slot Number Synchronization Auto RestoreSource Slot Number Synchronization Auto Restore

Source Slot Number Synchronization Auto Restore

Primary PC) 4 PS) net 1 PA) yes

Primary PC) 4 PS) net 1 PA) yesPrimary PC) 4 PS) net 1 PA) yes

Primary PC) 4 PS) net 1 PA) yes

Secondary SC) 4 SS) net 2 SA) yes

Secondary SC) 4 SS) net 2 SA) yesSecondary SC) 4 SS) net 2 SA) yes

Secondary SC) 4 SS) net 2 SA) yes

Tertiary TC) 4 TS) net 3 TA) yes

Tertiary TC) 4 TS) net 3 TA) yesTertiary TC) 4 TS) net 3 TA) yes

Tertiary TC) 4 TS) net 3 TA) yes

X) exit this menu

X) exit this menuX) exit this menu

X) exit this menu

A [0.0.0.60] [1,3] QUAD DATA >

A [0.0.0.60] [1,3] QUAD DATA >A [0.0.0.60] [1,3] QUAD DATA >

A [0.0.0.60] [1,3] QUAD DATA >

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 46 47

Kommentare zu diesen Handbüchern

Keine Kommentare

Verilink QUAD DATA (880-503319-001) Product Manual Bedienungsanleitung Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computerhardware Verilink QUAD DATA (880-503319-001) Product Manual