Verilink 8100A (34-00237) Product Manual Bedienungsanleitung Seite 111
- Seite / 311
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuration 4-37
Figure 4.56
Frame Relay Management Protocol Menu
2 Type the number that corresponds to the protocol on your network and press
Enter.
Configure Congestion Parameters
To configure Congestion Parameters, follow the steps below.
1 Type “3” on the Frame Relay Options menu to display the Fame Relay
Congestion Configuration menu (Figure 4.57).
Figure 4.57
Frame Relay Congestion Configuration Menu
2 Select Configure Transmit Congestion Parameters and then follow the on-
screen messages to
• FECN/BECN condition set size
• FECN/BECN condition clear size
• FECN/BECN max number of bytes to store
− or −
Select Configure Receive Congestion Parameters and then follow the on-
screen messages to
• FECN/BECN condition set size
• FECN/BECN condition clear size
• FECN/BECN max number of bytes to store
4 Reset the IAD for changes to take effect.
- Verilink 1
- 8000 Series 1
- 81xx/82xx/83xx/85xx 1
- Reference Manual 1
- Canadian Emissions 3
- Requirements 3
- Table of Contents 11
- Chapter 3 Administration 12
- Chapter 4 Configuration 13
- Chapter 5 Reports 16
- Appendix A Menu Map 17
- Appendix B Specifications 17
- Chapter 8 Verification 17
- Appendix E Glossary 21
- About this Manual 23
- Typographic Conventions 24
- Support from Verilink 25
- Returning a Unit to Verilink 26
- NTRODUCTION 27
- Low POTS Port Features 28
- Figure 1.1 29
- Figure 1.2 29
- 10/100 LAN 30
- Ground, the use of 30
- Figure 1.3 30
- Figure 1.4 30
- Figure 1.5 31
- Figure 1.6 31
- High POTS Port Features 32
- Figure 1.7 33
- 1-8 8000 Series 34
- Introduction 1-9 35
- 1-10 8000 Series 36
- Unpacking the IAD 37
- Installing the IAD 38
- • Connect the IAD to a PC 39
- • Log in to the IAD 39
- • Set the IP address 39
- Figure 2.1 40
- Quick Start Guide 2-5 41
- Figure 2.2 42
- 8308 Available Interfaces 43
- 8208 Available Interfaces 43
- Resetting the IAD 44
- Connecting via Telnet 45
- 2-10 8000 Series 46
- Basic IAD Configuration 47
- Ethernet LAN Connection 48
- WAN Connections 48
- Telephone Connections 48
- Life Line Connection 48
- Confirming Proper Setup 49
- 2-14 8000 Series 50
- DMINISTRATION 51
- Password Configuration Menu 52
- Change User ID 53
- Change User Password 54
- RADIUS Server Settings 54
- Setting Up SNMP 55
- SNMP Configuration Menu 56
- Enable/Disable SNMP via IP 57
- Enable/Disable SNMP via EOC 57
- Configure System Contact 57
- Configure System Name 58
- Configure System Location 58
- Configure SNMP Community 58
- Administration 3-9 59
- SNMP V3 Configuration Menu 60
- LAN Configuration Menu 61
- Upgrading the System 61
- Copying the Source Files 62
- Upgrading via TFTP 62
- Utilities Menu 63
- Ping Utility 64
- Trace Route 64
- Configure Console Baud Rate 64
- Configure Console Timeout 65
- Set System Defaults 66
- Display Event Log 67
- Clear “Last Reset Reason” 67
- Time Menu 67
- NTP Server Menu 68
- Time Zone Menu 68
- Display Configuration File 69
- File System Menu 69
- Type File 70
- Copy File 70
- Rename File 70
- Delete File 70
- File Transfer Menu 71
- Update ACOS [acos.bin] 72
- Update Entire System 72
- File Transfer Utilities 72
- TFTP Server Menu 73
- 3-24 8000 Series 74
- ONFIGURATION 75
- WAN Configuration 76
- Figure 4.1 77
- 4-4 8000 Series 78
- WAN Configuration Menu 79
- Figure 4.4 80
- Figure 4.5 80
- Figure 4.6 80
- Figure 4.7 81
- Figure 4.8 81
- Figure 4.9 81
- SDSL Configuration Menu 82
- IMAS First Speed Option Menu 83
- SDSL Auto Cycle Speed Table 84
- Quick Configuration Menu 85
- T1 Configuration Menu 86
- Select T1 Frame Mode Menu 86
- Select Line Build Out Menu 87
- Channel Configuration Menu 88
- Select Tx Clock Source Menu 89
- E1 Configuration Menu 90
- E1 Frame Mode Menu 90
- Configure S-Bits Menu 91
- Select Loopback Configuration 91
- ADSL Configuration Menu 93
- ADSL Standards Menu 94
- SHDSL Configuration Menu 94
- USI Configuration Menu 95
- Configure Datalink Protocol 96
- Configuration 4-23 97
- Configure ATM PVCs 98
- Figure 4.36 99
- Figure 4.37 99
- Figure 4.38 100
- Figure 4.39 100
- AAL2 Audio Profile Format 101
- PPP Authorization Menu 102
- IPCP Configuration Menu 102
- Configuration 4-29 103
- Configure ATM Options 104
- Configure DLCIs 105
- Figure 4.47 106
- Figure 4.48 106
- Figure 4.49 106
- Figure 4.50 107
- Configure Frame Relay Options 108
- Configure Fragmentation 109
- CopperMountain DSLAMs 110
- Figure 4.56 111
- Figure 4.57 111
- Router Configuration 112
- Router Configuration Menu 113
- Configure Port IP Address 114
- Unconfigure Port IP Address 115
- 4-42 8000 Series 116
- Router Modification Menu 117
- Enable/Disable RIP 118
- Configure RIP Version by Port 119
- Configure DNS Client 120
- Configure DHCP Client 121
- Configure DHCP Relay 121
- Configure Telnet Server Port 122
- Configure IP QoS 123
- Configure IP Filtering 123
- Figure 4.66 124
- Figure 4.67 124
- Configure Domain Name 125
- Configure Host Name 126
- Remove Host and Domain Names 126
- Display Route Table 126
- Bridge Configuration 127
- Bridge Configuration Menu 128
- IP Over Bridging 129
- 4-56 8000 Series 130
- Bridge Aging Timer 131
- 4-58 8000 Series 132
- Configuration 4-59 133
- Voice Path Configuration 134
- Basic Voice Path Setup Tasks 135
- Voice Configuration Menu 135
- AAL2/LES CAS 136
- AAL2/LES Configuration Menu 137
- Enable/Disable Ports 138
- CAS Options 138
- Configuration 4-65 139
- Manual ATM Pace Control Menu 140
- JetStream 141
- 4-68 8000 Series 142
- CopperCom 143
- CopperCom Configuration Menu 144
- AAL2/LES CCS-ELCP 145
- Variant/Interface Management 146
- Clear AAL2 Channel Statistics 147
- CODEC Management Menu 148
- Port Administration Menu 149
- SIP Management Menu 150
- Configuration 4-77 151
- Set Jitter Delay 153
- Voice Port Settings 153
- Voice Port Configuration Menu 154
- Busy Out Line Settings Menu 154
- Start Mode Selection Menu 154
- Configuration 4-81 155
- Figure 4.96 156
- Figure 4.97 156
- Configure Loop Gain Menu 157
- Display Compander Mode ( 158
- -law, A-law) 158
- Interworking Connections 159
- Figure 4.102 160
- Interworking Connections Menu 161
- FRF.5 DE Mapping Menu 161
- FRF.5 CLPI Mapping Menu 162
- FRF.8 Translation Menu 162
- FRF.8 DE Mapping 162
- Firewall Configuration 163
- DHCP Server Configuration 164
- Enable/Disable DHCP Server 165
- Configure DHCP Client Entry 166
- Display DHCP Configuration 167
- 4-94 8000 Series 168
- Addresses 169
- Display DHCP Entry Details 169
- Multicast Configuration 170
- Multicast Configuration Menu 171
- Figure 4.112 172
- Show IGMP Group 173
- Show IGMP Querier 173
- Show Multicast Routing Table 174
- Show PIM Neighbor 174
- NAT Configuration 175
- Figure 4.113 176
- Configure NAT Port Range 177
- 4-104 8000 Series 178
- Configure NAT Alias Entry 179
- Display NAT Statistics 180
- Display NAT Connection Table 181
- Display NAT Alias Table 182
- Clear NAT Statistics 182
- Setting PPP Options 183
- Derived Timing Menu 184
- Reports Menu 185
- Current Configuration Report 186
- Reports 5-3 187
- Network Statistics Reports 188
- packet buffers, etc 189
- IGMP Statistics Report 190
- Received Packet Information 191
- Sent Packet Information 191
- IP Statistics Report 192
- PIM Statistics Report 193
- TCP Statistics Report 194
- UDP Statistics Report 196
- Clear Network Statistics 196
- Interface Statistics Reports 197
- Display Interface Statistics 198
- Display DLCI Statistics 199
- Display ATM PVC Statistics 200
- Reports 5-17 201
- Common AAL Statistics Report 202
- PPP Statistics Report 204
- Display Bridge Statistics 205
- Media Statistics Reports 206
- Figure 5.7 207
- Received Data 207
- Display ATM Statistics 208
- Reports 5-25 209
- 5-26 8000 Series 210
- Reports 5-27 211
- 5-28 8000 Series 212
- Display Ethernet Statistics 213
- Display POTS Statistics 214
- Route Table Report 215
- ARP Table Report 215
- Bridge Status Report 216
- System Uptime Report 217
- Memory Statistics Reports 217
- Memory Statistics Menu 218
- Tasks Run Time 219
- Zero All Statistics 220
- NTERFACE 221
- Command Line Syntax 222
- Command Line Interface 6-3 223
- 6-4 8000 Series 224
- Command Line Interface 6-5 225
- 6-6 8000 Series 226
- Command Line Interface 6-7 227
- 6-8 8000 Series 228
- Command Line Interface 6-9 229
- 6-10 8000 Series 230
- Command Line Interface 6-11 231
- 6-12 8000 Series 232
- Command Line Interface 6-13 233
- 6-14 8000 Series 234
- Command Line Interface 6-15 235
- 6-16 8000 Series 236
- Command Line Interface 6-17 237
- 6-18 8000 Series 238
- ROUBLESHOOTING 239
- IAGNOSTICS 239
- POTS Diagnostics 240
- Hotline Test 241
- Ring Test 241
- On/Off Hook Test 242
- Troubleshooting the IAD 243
- Cannot receive or send data 244
- 7-8 8000 Series 246
- ERIFICATION 247
- Testing the IAD 248
- Maintenance 248
- 8-4 8000 Series 250
- PPEN DIX 251
- A-2 8000 Series 252
- PECIFICATIONS 253
- Data Features 254
- WAN Features 254
- Network Interfaces 254
- Frame Relay 255
- Configuration and Management 256
- Security Features 256
- Management Interfaces 256
- Diagnostics 256
- Environmental 257
- Connector Pin Assignments 258
- T1/E1 (8216s and 8224s) 259
- Industry Listings 263
- Signal RS-530 V.35 RS-449 265
- Voice Features 266
- Specifications B-17 269
- SDSL (8316s and 8324s) 271
- Link, Voice 284
- Weight: 1.8 lb 284
- B-36 8000 Series 288
- LED Function 292
- Specifications 292
- PPLICATIONS 293
- Voice-only Applications 294
- Voice and Data Applications 294
- Configuring NAT Port Range 295
- Configuring NAT TCP Timeout 295
- Configuring NAT UDP Timeout 295
- IP Filtering 296
- Information Policy 297
- Filtering Interface 297
- Figure D-1 298
- Applications Notes D-7 299
- Filter Rules 300
- Matching Parameters 301
- D-10 8000 Series 302
- Keep History 303
- Dial Plan 304
- Applications Notes D-13 305
- D-14 8000 Series 306
- PP ENDIX 307
- E-2 8000 Series 308
- Glossary E-3 309
- E-4 8000 Series 310
Verwandte Produkte und Handbücher für Computerhardware Verilink 8100A (34-00237) Product Manual
Computerhardware Verilink APS 2000 T1 Line Protection (880-502411-001) Produ Bedienungsanleitung
(87 Seiten)
(87 Seiten)
Computerhardware Verilink AS56/56Plus (896-502588-001) Product Manual Bedienungsanleitung
(130 Seiten)
(130 Seiten)
Computerhardware Verilink AS2000: The Basics (880-502981-001) Product Manual Bedienungsanleitung
(179 Seiten)
(179 Seiten)
Computerhardware Verilink Access Manager 2000 (896-502037-001) Product Manua Bedienungsanleitung
(400 Seiten)
(400 Seiten)
Computerhardware Verilink ConnecT 56K DSU (896-502110-001) Product Manual Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Computerhardware Verilink Craft Interface (No Part Number) Product Manual Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Computerhardware Verilink DIDCSU 2912 (880-502646-001) Product Manual Bedienungsanleitung
(107 Seiten)
(107 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern